Twined or furled leaders
Step two - preparation
By Henk Verhaar
So how does one make such a twined leader butt? I'll start out by describing the needed materials, then describe the basic procedure for a standard butt, ending with an indication of all the possible customizations.
Materials needed
Most important is what I'll call the leader board. This basically is a 2.4 m long, 25 cm wide wooden board with a smaller
board overhanging the top, three hooks attached to the underside of the overhang, and a number of plugs, attached to the board, beneath the two outermost hooks. See figures 1 and 2 for general idea of setup and for some standard measurements.
The board can be homemade from available scrap wood having the correct dimensions -- attachment of the overhang is with dowels and glue. The plugs are cut sections from a round stick (like a broomstick) about 2 cm in diameter, and are attached to the board with dowels. Use the distances shown in figure 2 to start with. They can be either glued down, or just stuck into holes in the board -- this makes it possible to alter the custom taper of the butt by changing the plugs to a different set of holes. More on this later. Draw a line across the board at approximately 2.00 m down from the hooks (or 90% of the distance from the hooks to the lowest plugs).
Weights
Next item is some heavy lead weights with attachment loops. I use surf casting lead weights with anchors (these are normally bent outwards to assist anchoring of the weight to the bottom, but in our case are kept straight so as to facilitate turning the weight), and a heavy wire snap as attachment loop, although a heavy paperclip could be adjusted for this purpose also. See also figure 6.
Other stuff
Some superglue will be necessary to seal the two ends -- again, more on this later -- and finally a roll of mono to make the leader butt. Yes that's right, you need just ONE roll, one strength of mono, to make an entire butt. I usually buy this in 100m rolls. 100 m (110 yards) will make you three complete butts. For trout and other light line leaders I use 12/00 mm dia. mono (this is similar to 6X). For light saltwater work I may step this up to 15/00 (5X) and for heavy pike streamer leaders even 18/00 (4X). But to get started, you can get by with just one 100 m roll of 6X.
Did you find the above interesting? | People who looked at the above also looked at:
This is a way of making a loop on a fly line that will give you a very neat and tiny loop and a smooth transition between the different parts of a rig.
One of GFF's all-time most popular articles and downloads just got better! Download two new upgrades for FREE! 1) Leadercalc2007, enhanced with new formulas and label making features and 2) the all new GFF's Leader Guide, a 28-page PDF book you can use for your classroom or personal use.
In this article I will try to cover some advantages and disadvantages of the shooting head over the WF line, and I will thoroughly describe the way you can configure a good shooting head system for your rod. The article will teach you how to calculate, make and trim a shooting head. It will also tell you how to cast it - just on the introductory level.
Leaders fall in several categories. These all serve the same purpose: transmitting the energy fra the fly line to the fly in a gentle, yet firm way. The different types each have their advantages and disadvantages, and selecting one is often a question of compromises.
When I first started fishing with a fly rod, I spent a lot of time tying compex knots to join the different part of the rig. I wish someone had told me about loops when I started, because they would have saved me a lot af work.
| A few random articles for your entertainment
|
| 
Submitted June 27th 2008
Dear Henk: Is it possible to build the furled leader with different thread weights such as 3/0 for the butt of the leader, 6/0 for the mid sections, and 8/0 for the tippets. And, how would I go about doing that. Thank you..